Our Equipment Catalog
Commercial-grade machinery for every operation. Each product built to withstand daily industrial use.
Low Stock
4L Planetary Ball Mill with 4 Jars
Processes four samples at once in four included 1000ml stainless steel jars and handles up to 4000ml per batch. The 1500W motor drives a gear transmission built to resist burnout through extended cycles. A built-in cooling fan keeps the motor stable through back-to-back grinding sessions. The LED display shows real-time status while an automated timer stops the mill once it reaches the set point. Dry or wet grinding breaks samples down to 0.1 microns, fine enough for side-by-side comparisons across four jars. A variable frequency drive holds voltage steady on the digital display. It protects the motor through 110V runs across geology and metallurgy labs.
- Gear-driven motor resists burnout and noise
- Programmable LED display with auto-stop timer
- Four 1000ml jars, 4000ml batch capacity
- Grinds particles as fine as 0.1 microns
- Variable frequency drive stabilizes voltage digitally
Low Stock
Portable Line Boring & Welding Machine
This portable line boring and welding machine bores 55-300mm holes and welds 50-300mm joints on-site, no shop trip needed. A 110V, 2.35KW servo motor drives smooth cutting at low speeds while keeping noise down. The heat-treated alloy steel boring bar handles a 260mm machining stroke for concentric and parallel holes. A red emergency stop button on the control handle cuts power instantly mid-operation. Infinitely variable speed control lets technicians dial the feed rate to the exact cut. Crews repair connecting rod holes on excavators, cranes, and loaders without pulling the machine apart.
- 2.35KW 110V servo motor
- Bores 55-300mm, welds 50-300mm
- 260mm max machining stroke
- Red emergency stop button
- Infinitely variable speed control
Low Stock
5T Telescopic Forklift Jib Boom
Slide the forks into two 3.15 x 7.87 in openings and lift construction materials up to 11,000 lb straight off the pallet. Extend the telescopic arm to 96.5 inches to clear obstacles and swing loads around tight corners on a busy site. The quench-hardened hook accepts wire rope or chain, so crews switch rigging in seconds without swapping the boom. Two knobs and a safety chain lock the base to the forks, holding the arm steady through a full 5T lift. The fully welded carbon steel base absorbs daily impacts at warehouses and construction sites without cracking at the welds. The yellow finish keeps the boom visible across a crowded loading dock.
- 11,000 lb (5T) load capacity
- Telescopic boom extends to 96.5 in
- Quench-hardened hook for rope or chain
- Fork openings 3.15 x 7.87 in
- Chain and knobs lock boom to forks
Low Stock
31.5-Inch Rotary Bottle Accumulation Table
The 31.5-inch turntable feeds round and square bottles onto a labeling or filling line without manual sorting. Adjust the guide rails to fit bottles up to 3.54 inches in diameter, then lock the speed dial to match the filler's pace. Slide the stainless steel tray into place under the 32.3-inch conveyor line for a level bottle inlet. The interconnection doubles as a buffer platform, so operators shorten the conveyor run and use less steel in the frame. Run it on a standard 110V outlet, no upgraded wiring or dedicated line required. Position the 34.3 x 24.8 x 44.48-inch frame on the shop floor, and it holds steady through a full shift of round-bottle accumulation.
- Adjustable bottle range up to 3.54 inches
- Stepless speed control for line pacing
- Stainless steel construction for long service life
- Doubles as buffer platform to shorten conveyors
- 110V power, no special wiring needed
Low Stock
5mm Double-Blade Meat Slicer
Feed a slab of pork through the 90mm inlet and this double-blade cutter shreds it on the first pass, dices it on the second. Push a batch through and the 52-degree hardened blades cut 250 kg of meat every hour. Run the machine through a full shift and two 550W motors keep worm-gear torque steady under load. Hose down the 304 stainless steel body after each shift and it resists rust and daily wear. Swap in a 3mm or 15mm blade set when a recipe calls for thinner shreds or chunkier dice. An internal safety switch locks the motor the instant the blade housing opens, so fingers stay clear of the blade edge.
- Double-blade design shreds then dices meat
- 52-degree hardened steel blades
- 304 stainless steel body
- Replaceable blades from 3mm to 15mm
- Safety interlock locks blade housing
Low Stock
13-Inch Digital Creasing & Perforating Machine
Feed coated stock up to 350g/m² into the 13-inch bed, and the digital panel locks creases to +/-0.3mm accuracy. Draw the perforating tool set from its storage bin and swap it in under a minute for laminated sheets. Run a full batch through at up to 2600 A4 sheets per hour without a paper jam. Turn the hex wrench on the pressure holes before a heavy stock run, and the rollers ease off to protect varnish paper from cracking. Set the panel for up to 32 creases on one sheet, then check the fault light before the next batch starts. Side vents clear heat from the housing during long runs, and output stays consistent past the hundredth sheet.
- Combines creasing and perforating in one unit
- +/-0.3mm precision digital control panel
- Tool sets swap in seconds
- Hex-wrench pressure adjustment for paper thickness
- Side vents cool machine during high-speed runs
Low Stock
Electric Rotating Cattle Body Brush
The 100W motor swings a 23.6-inch brush across a cow's back and flank at a steady, animal-safe speed. Bristles reach the full body in one pass and ease tension without irritating skin. One unit services up to 60 cows or horses and runs near round-the-clock on low power draw. Independently fixed bristles hold together through months of daily rubbing against hide and mud. Over-current protection stops the motor the moment the brush jams against a post or gate. Bolt it to a barn wall or pole in under an hour with the included U-shaped bracket.
- 360° swinging brush with adjustable speed
- 23.6-inch bristle head for full-body reach
- Services up to 60 cows per unit
- Independently fixed, shed-resistant bristles
- Over-current protection stops motor on jam
Low Stock
36-Die Manual Cutter Bending Machine
Feed a die-cutting blade into the CX-25B and bend a 65° angle without wiring in a compressor or motor. Set the punch-and-die pair to shape a 0.39-inch circular diameter with one pull of the handle. Nitrided punches hold ±0.1° bending accuracy across every changeover. Swap between 15 interchangeable punches and 21 dies to match a new blade thickness in under a minute. Pull from the 36-die set for prototyping runs and small batches a pneumatic bender can't justify. Form the next crease rule by hand, no compressor hookup or power cord needed.
- 36-die set with 65° bend angle
- ±0.1° bending accuracy via nitrided punches
- 15 interchangeable punches, 21 dies
- No compressor or electricity required
- Manual operation for small-batch prototyping
Low Stock
6mm Feed Pellet Mill with 3 Rollers
Load corn, alfalfa, or soybeans into the widened stainless steel inlet, and the three-roller grinding head pushes out 330 lbs of pellets per hour. The 3.5kW motor drives hardened rollers and a cast-iron grinding disc built to survive daily farm use. Swap the grinding disc from 2mm to 8mm to match rabbit, poultry, or cattle feed. A built-in voltage display flags power swings before they stall a batch. Adjust roller position to shorten or lengthen each pellet without extra tools. Four wheels roll the 70 x 28.5 x 88 cm frame between the barn and the feed room in seconds.
- 3-roller grinding head, 330 lbs/h output
- 3.5kW motor with hardened rollers
- Built-in voltage display for stability
- Interchangeable disc, 2mm to 8mm
- Four wheels for easy relocation
Low Stock
HEPA Laminar Flow Clean Bench
Creates a laboratory-grade clean zone for phone LCD repair and micro-electronics assembly. The HEPA filter captures 99.99% of particles down to 0.3 microns before air reaches the bench. A multi-wing centrifugal fan pushes air at 0.35-0.55m/s across the 47.2 x 23.6 x 29 inch work surface. A 3-gear switch dials that airflow up or down for louder or quieter tasks. The 40x40cm aluminum frame and reinforced corners hold the bench steady through daily use. A conductive PVC curtain surrounds the station and drains static before it reaches open circuit boards. Modular panels let technicians link several units into one assembly line for larger batches.
- HEPA filter traps 99.99% of 0.3-micron particles
- 3-gear adjustable airflow, 0.35-0.55m/s
- 40x40cm reinforced aluminum frame
- Anti-static conductive PVC curtain
- Modular design links multiple units
Low Stock
4-Well Propane Steam Table Warmer
Feeds a buffet line from four 13 x 10.5 x 4 in wells, each sized for a standard 1/2 sheet pan. Turn the included gas regulator valve to dial propane flow and hold steam-table heat through a full event. The 304 stainless steel body resists rust after repeated wash-downs in a catering kitchen. Open the drain faucet to empty each well in under 30 seconds. Adjust the firepower gear mid-service to keep gravy hot without scorching the pan below. Haul it to a backyard wedding or a food-truck lot with no electrical hookup required.
- Four 13x10.5x4in wells for 1/2 pans
- 304 stainless steel resists rust and corrosion
- Included gas regulator valve controls propane flow
- Faucet drain empties each well fast
- Adjustable firepower gear dials heat precisely
Low Stock
2-Pan Propane Gas Steam Table
The haywhnkn steam table holds two standard 1/2-size sheet pans, each well measuring 13 x 10.5 x 4 inches for full-tray buffet spreads. A propane gas regulator valve ships in the box; adjust the inlet flow to set temperature at the burner. Built from 304 stainless steel, the twin wells resist rust through repeat wash cycles and keep dishes heated across a full catering shift. A side faucet drains each well without lifting the pan, cutting post-party cleanup to minutes. Adjustable firepower gears dial heat from a light simmer to a rolling boil, so sauces stay hot without scorching.
- Propane gas with included regulator valve
- Two 13 x 10.5 x 4 in wells
- 304 stainless steel construction
- Built-in faucet drain
- Adjustable firepower control
Low Stock
75-Drawer Bolt and Nut Storage Cabinet
Organizes bolts, nuts, and drill bits across 75 individual drawers instead of one tangled toolbox. The cabinet body uses cold-rolled steel, laser-welded at every seam and powder-coated for an odor-free, chip-resistant finish. Each ABS drawer measures 7.8 x 3.9 x 1.9 inches and locks against slipping, so pulling one open never spills parts across the bench. Built-in dividers separate loose screws from grinding bits and stray receipts in the same tray. Mount it on a workshop wall or set it on a warehouse shelf, and labeled drawers turn a five-minute parts search into a ten-second grab.
- 75 individual bolt and nut drawers
- Laser-welded cold-rolled steel cabinet body
- Anti-slip drawers with adjustable dividers
- ABS drawers sized 7.8 x 3.9 x 1.9 in
- Odor-free powder-coated finish
Out of Stock
Sliding Frame T-Shirt Screen Printing Press
Slide the screen frame back 11.8 inches to lift a finished T-shirt off the 22 x 18 inch pallet without snagging the fabric. Lock that position with a screw, then load the next shirt in seconds. A screw rod at the support plate dials in the lifting angle, so gravity-balance plates keep every pass level. The frame lifts on its own once printing finishes, so wet ink never touches your hands. Clamps span 9.4 inches wide and 2.7 inches tall to fit frames up to 2 inches thick. Bolt the press to a workbench, then run T-shirts, wood panels, or ceramic tile through the same station.
- 11.8-inch sliding frame for shirt removal
- 22 x 18 inch printing pallet
- Gravity-balance plates for stable printing
- Auto-lifting screen frame after printing
- Clamps fit frames up to 2 inches thick
